That drip is costing you more than it sounds like. Expert faucet repair in Phoenix, Arizona plus clean, code-compliant sink and fixture installation.
All Brands & Finishes
Transparent, Upfront Pricing
100% Satisfaction Guarantee
Fixtures fail gradually, then all at once. Call for faucet or sink service if:
A faucet drips constantly even when fully closed
Water pooling in the cabinet beneath the sink
Handles that stick, spin or no longer control temperature
Corrosion, mineral crust or staining around the base
You are remodelling a kitchen or bathroom
Persistent slow drainage at a single sink
At APES, faucet and sink service covers the fixture, the supply and the drain beneath it:
Cartridge, washer and O-ring replacement
Dripping and leaking faucet repair
Drop-in, undermount and farmhouse sink installation
Shutoff valve replacement and aerator descaling
Under-sink work is where small mistakes turn into cabinet replacements. Here is why professional service is essential:
A slow supply or trap leak destroys particle board cabinet bases long before you see water on the floor. If you suspect there are household leaks you cannot see, our leak detection team can confirm it in an hour.
Faucet internals are brand and model specific. The right part fixes it permanently; a generic one leaks again in months.
Phoenix water runs 12-20 grains of hardness, which clogs aerators and seizes cartridges. We descale and select fixtures that hold up here.
P-traps and drain arms need correct fall. Bad slope means standing water, odour and recurring clogs.
Undermount and stone installations need correct support and sealing. Wrong technique cracks the counter.
We identify whether the problem is the fixture, the supply or the drain, and recommend repair or replacement honestly.
You receive a flat quote covering parts and labour. Most faucet repairs complete in under an hour.
Our plumbers complete the repair or set the new fixture with fresh supply lines, correct sealant and proper drain assembly.
We run hot and cold at full flow, check every joint for leaks, and confirm drain flow and shutoff function.
We clear the work area, haul the old fixture, and show you where the shutoffs are for future emergencies.
A dripping faucet wastes thousands of gallons a year and signals a problem that rarely stays small. Trust APES for faucet repair in Phoenix, Arizona, quoted upfront and fixed right.
Arizona’s mineral content is hard on fixtures. A little upkeep goes a long way:
Unscrew, soak in vinegar and rinse to restore flow lost to scale.
Run a dry hand along supply lines and the trap to catch moisture early.
Stiff handles mean a worn cartridge. Forcing them cracks the valve body.
Braided steel lines fail without warning and flood a room in minutes.
Abrasives and bleach damage finishes and rubber seals.
An angle stop that has never been turned usually will not turn when you need it.
Softened water dramatically extends fixture and cartridge life in Phoenix see water softener installation.
At APES, we’ve partnered with Momnt to make faucet & sink repair and installation easier on your budget. Keep the standard five-point financing block used across the site: Finance Projects Up to $55,000 · Fast Approval Process · 100% Digital Application · Flexible Monthly Payments · No Prepayment Penalties.
Finance Projects Up to $55,000
Fast Approval Process
100% Digital Application
Flexible Monthly Payments
No Prepayment Penalties
Most cartridge and washer repairs are modest flat-rate jobs. Replacing the fixture costs more but is often the better value on a faucet over ten years old. We quote before starting.
Modern faucets use cartridges rather than washers, and mineral damage to the valve seat can prevent a new part from sealing. That usually means the cartridge or the whole fixture needs attention.
Yes. A single slow fixture is almost always a scaled aerator, a clogged cartridge or a partially closed shutoff. Low water pressure in the house as a whole is a different problem that points to the pressure regulator, corroded piping or a hidden leak, and we test for it separately.
A standard replacement takes 1-2 hours. Sink installation, especially undermount or stone, takes longer.
Yes. We install customer-supplied fixtures and will tell you upfront if the mounting configuration will not fit your sink.
The three usual suspects are the supply line connection, the P-trap joints and the sink drain flange. We test each rather than guessing.
Valley water typically runs 12-20 grains per gallon, which is very hard. That scale is what clogs aerators, seizes cartridges and shortens the life of every fixture in the house.
Yes. Sensor faucets add electronics and solenoids to the failure list, and we service those alongside the mechanical parts.
